Real Mouse Tester
Accurate Browser Hardware Diagnostics • Zero Installation Required

Mouse test: buttons, double-click and scroll

Check left, right, middle, and side buttons (M4/M5). Spot faulty microswitch chatter under 75ms, detect reverse rotary encoder slips, test click speed (CPS), and measure USB polling rates up to 8000Hz.

Mouse test: buttons, double-click and scroll

Testing
0
0
Reverse: 0
Peak: 0/s
Left 0 Not tested
Middle 0 Not tested
Right 0 Not tested
Back 0 Not tested
Forward 0 Not tested

Polling rate

Press Start, then move in fast circles

0 Hz
Readings: 0
Median: 0 Hz
Within ±10% 100%

Click speed

0.0 Click to start
Clicks: 0 Time: 5.0s
Ready

Sensor and raw cursor input

Sensor test: ✓ Clear
Keep drawing across the pad
Reports 0
Skips 0
Longest gap 0.0ms
[ Technical Diagnostics ]

Real-Time Switch Debounce & Chatter

Sub-millisecond hardware intervals captured directly from physical switch micro-contacts.

⚡

Debounce & Switch Chatter Scanner

Detects abnormal micro-bounces (< 75ms)
75 ms
Fast Debounce (40ms) Chatter Threshold Relaxed (150ms)
Click buttons on the mouse above to record debounce actuation intervals...
🛡️

Hardware Health Summary

0 Defects
Health Score 100%
Audit Status PASSED
[ Architecture ]

How mouse input reaches the computer

Each click or movement passes through six steps on its way to this page. The online mouse tester reads the last one, so there is nothing to install.

6 steps
1

Physical Microswitch

Mechanical leaf springs or optical light-beams close circuit contacts on actuation. Mechanical switches create initial bounce vibration.

2

Optical Sensor

High-speed CMOS cameras (PAW3395 / HERO) capture 20,000+ surface snapshots per second to measure exact X/Y motion delta.

3

Onboard Controller

Internal MCU executes firmware debounce filtering to prevent accidental double-clicks and assembles USB HID data packets.

4

USB / 2.4GHz Report

Hardware transmits HID packets at 125Hz to 8000Hz (up to 0.125ms intervals) to your PC USB host controller endpoint.

5

Operating System HID

Windows / macOS / Linux HID driver translates raw sensor deltas into desktop cursor movement and dispatches interrupts.

6

Browser Pointer Events

W3C Pointer Events API captures raw pointerdown, wheel, and pointerrawupdate events with microsecond accuracy.

[ Physics & Mechanics ]

Why a mouse double-clicks

A worn switch can send two clicks for one press. Clicks less than 80 ms apart are flagged.

80 ms threshold
Good Switch (Clean Transition) 0ms Bounce
Single Crisp Contact Close

The switch contact drops cleanly below the voltage threshold. Firmware registers one single press cleanly.

Worn / Oxidized Switch (Chatter) Fault (<80ms)
Rapid Contact Micro-Bouncing

A worn spring opens and closes again and sends a second click within 24–75 ms, triggering an unintended double-click.

[ Troubleshooting ]

Mouse troubleshooting

5 problems
Symptom Common Cause Recommended Fix Diagnostic Tool
Clicks twice (Double-click) Worn or oxidized metallic microswitch Clean switch contacts or solder replacement Double-click test →
Jittery / skipping cursor Dust or hair blocking optical sensor lens Clean lens gently with dry cotton swab Sensor test →
Laggy / stuttering cursor Low USB polling rate or power-saving mode Set polling rate to 1000 Hz in mouse software Polling rate test →
Connection drops Weak 2.4GHz wireless signal or low battery Move USB dongle closer or recharge battery Polling rate test →
Reverse scrolling jumps Dirty or worn mechanical rotary encoder Use compressed air or electrical contact cleaner Scroll wheel test →
[ Latency Guide ]

Choosing a polling rate

Polling rate is how many times a second the mouse reports its position. Lower delay means faster response.

7 tiers
8.0 ms
125 Hz
4.0 ms
250 Hz
2.0 ms
500 Hz
1.0 ms
1000 Hz
0.5 ms
2K Hz
0.25 ms
4K Hz
0.125 ms
8K Hz
Office & casual (125–250 Hz) Saves battery life, low CPU overhead.
Casual gaming (500 Hz) Smooth motion on 60Hz–144Hz monitors.
FPS Standard (1000 Hz) Best balance for CS2, Valorant & Apex.
Pro Esports (2K–8K Hz) Zero input lag on 240Hz–540Hz displays.
[ Multi-Page Suite ]

All 16 Hardware & Gaming Tools

Dedicated standalone interactive testing pages for every aspect of your mouse and monitor.

Explore All Tools →
[ FAQ ]

Frequently asked questions

How do I check if my mouse is working properly?

Press every button in the test area, scroll both ways, and run the polling rate test. A missed or doubled click points to a worn switch, while erratic jumps indicate a dirty encoder or sensor.

My mouse is rated 1000 Hz. Why does the test show 125 Hz?

Make sure your polling rate is set to 1000 Hz in your mouse driver software (G Hub, Synapse, etc.). Wireless mice may also drop to 125 Hz in power-saving mode.

Does one possible double-click mean my mouse is broken?

Not necessarily. It only indicates hardware failure if double-click chatter repeats consistently across 2–3 separate tests of the same button.

Why doesn't the browser go back when I press the side button?

Inside the test arena, we safely intercept Back (M4), Forward (M5), and right-click context menus so you can test all 5 buttons without navigating away from the page.

Does this test upload my data?

No. All mouse tests execute 100% locally inside your web browser sandbox with zero telemetry or server uploads.

Does it work with Logitech, Razer, and Apple Magic Mouse?

Yes! Because it reads standard browser Pointer and Wheel events, it works seamlessly with Logitech G, Razer, SteelSeries, Zowie, Endgame Gear, and Apple Magic Mouse across Windows and Mac.